View SA57608_172537.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

INTEGRATED CIRCUITS
SA57608 One-cell Lithium-ion battery protection with over/undercharge and overcurrent protection
Product data Supersedes data of 2001 Oct 03 2003 Oct 29
Philips Semiconductors
Philips Semiconductors
Product data
One-cell Lithium-ion battery protection with over/undercharge and overcurrent protection
SA57608
GENERAL DESCRIPTION
The SA57608 is a single-cell Li-ion protection IC, and is an improved version of the NE57600, with different pinout. Its over and under voltage accuracies are trimmed to within 25 mV (5%) over the entire battery pack operating temperature range. The SA57608 is available in various over and undervoltage limits. There is a discharge overcurrent protection circuit which can protect the battery pack against an accidental short-circuit. The overcharge trip point has a time delay which can be programmed externally. It is packaged in a space-saving 6-lead small outline package and requires two external N-channel MOSFETs and a minimum of passive parts.
FEATURES
* Trimmed overvoltage trip point to within 25 mV * Programmable overvoltage trip time delay * Trimmed undervoltage trip point to within 25 mV * Very Low undervoltage quiescent sleep current 0.05 mA * Discharge overcurrent cutoff * Low operating current (10 mA) * 6-lead small outline package (SOP004)
SIMPLIFIED SYSTEM DIAGRAM
APPLICATIONS
* Cellular phones * Personal digital assistants * Palmtop computers
V+ 100 VCC 5
0.01 F 0.1 F Li-ION CELL GND 6 DF 1 CF 3 CDLY 4
SA57608
2
VM
0.1 F
1 k V-
DISCHARGE FET
CHARGE FET
SL01568
Figure 1. Simplified system diagram.
2003 Oct 29
2
Philips Semiconductors
Product data
One-cell Lithium-ion battery protection with over/undercharge and overcurrent protection
SA57608
ORDERING INFORMATION
PACKAGE TYPE NUMBER SA57608XD DESCRIPTION Plastic small outline package; 6 leads; body width 1.8 mm VERSION SOP004 TEMPERATURE RANGE -20 to +85 C
NOTE: The device has six protection parameter options, indicated by the X on the order code, and defined in the following table.
TYPICAL PROTECTION PARAMETERS
Part Number SA57608Y SA57608B SA57608C SA57608D SA57608E SA57608G Overcharge detection voltage (V) 4.350 0.050 4.280 0.025 4.295 0.025 4.350 0.050 4.275 0.025 4.280 0.025 Overcharge detection hysteresis voltage (mV) 180 180 150 180 200 200 Over-discharge detection voltage (V) 2.30 0.070 2.30 0.058 2.30 0.058 2.30 0.070 2.30 0.058 2.30 0.058 Overcurrent detection voltage (mV) 150 30 75 30 200 30 200 30 100 30 100 30
Part number marking
Each device is marked with a four letter code. The first three letters designate the product. The fourth letter, represented by `x', is a date tracking code. Part number SA57608YD SA57608BD SA57608CD SA57608DD SA57608ED SA57608GD Marking AGXx AGYx AGZx AHAx AHBx AHDx
PIN CONFIGURATION
DF VM CF 1 2 3 6 5 4 GND VCC CDLY
SL01569
Figure 2. Pin configuration.
PIN DESCRIPTION
PIN 1 2 3 4 5 6 SYMBOL DF VM CF CDLY VCC GND DESCRIPTION Discharge detection pin. This drives the gate of the discharge N-ch FET. Monitor pin. Detects overcurrent and the presence of a charger. Charge FET pin. This drives the gate of the charge control N-ch FET. Charge Time Delay pin. The capacitor connected to this pin sets the delay. Positive supply voltage input pin. Connect to positive terminal of the cell. Ground pin. Connect to negative terminal of the cell.
MAXIMUM RATINGS
SYMBOL VIN VCF(max) VVM(max) Topr Tstg PD Input voltage CF pin voltage VM pin voltage Operating ambient temperature range Storage temperature Power dissipation PARAMETER MIN. -0.3 VCC - 28 VCC - 28 -40 -40 - MAX. +12 VCC + 0.3 VCC + 0.3 +85 +125 150 UNIT V V V C C mW
2003 Oct 29
3
Philips Semiconductors
Product data
One-cell Lithium-ion battery protection with over/undercharge and overcurrent protection
SA57608
ELECTRICAL CHARACTERISTICS
Characteristics measured with Tamb = 25 C, unless otherwise specified. SYMBOL VDD1 IDD ISLP VDD(min) PARAMETER Operating input voltage Supply current Sleep current Minimum operating voltage for 0 V charging CONDITIONS VCC - GND; Voltage defined as VDD to VM VCC = 3.9 V; VM = 0 V VCC = 2.0 V VCC - GND SA57608Y SA57608B VO ( ) OV1(th) Over-charge Over charge voltage threshold Tamb = 0 C 50 C; VBATT : L H SA57608C SA57608D SA57608E SA57608G SA57608Y SA57608B VO ( OV1(hyst) ) Over-charge Over charge hysteresis VCC : H L SA57608C SA57608D SA57608E SA57608G SA57608Y SA57608B VUV(th) () Over-discharge Over discharge threshold voltage VCC : H L SA57608C SA57608D SA57608E SA57608G SA57608Y SA57608B VOC ( ) OC1(th) Overcurrent threshold VVM : L H SA57608C SA57608D SA57608E SA57608G VOV(rel) tOV(DLY) tOV tOC(DLY) VOC2 tDLY(SC) RSC VCFET(off) VCFET(on) VDFET(off) VDFET(on) Release voltage for over-discharge Over-charge delay time Over-discharge delay time Over-current delay time Short protection voltage Short detect delay time Reset resistance for excess current protection Nch ON voltage of CFET Pch ON voltage of CFET Nch ON voltage of DFET Pch ON voltage of DFET CTD = 0.01 F; VCC = 4.0 V to 4.4 V VCC = 3.6 V to 2.2 V VM : 0 V 0.5 V VCC = 3.0 V VCC = 3.0 V VCC = 3.6 V; VM = 1.0 V IOL = 50 mA; VCC = 4.4 V IOH = 50 mA; VCC = 3.9 V IOL = 50 mA; VCC = 2.2 V IOH = 50 mA; VCC = 3.9 V MIN. 1.5 - - - 4.30 4.255 4.27 4.30 4.25 4.255 - - - - - - 2.23 2.242 2.242 2.23 2.242 2.242 120 45 170 170 70 70 4.12 61 5 9 VCC-1.2 - 50 - 3.4 - 3.4 TYP. - 3.0 0.3 - 4.35 4.280 4.295 4.350 4.275 4.280 180 180 150 180 200 200 2.30 2.30 2.30 2.30 2.30 2.30 150 75 200 200 100 100 4.17 77 8 13 VCC-0.9 5 100 0.35 3.7 0.2 3.7 MAX. 10 8.0 0.6 1.2 4.40 4.305 4.32 4.40 4.3 4.305 - - - - - - 2.37 2.358 2.358 2.37 2.358 2.358 180 105 230 230 130 130 4.22 93 11 17 VCC-0.6 50 150 0.5 - 0.5 - UNIT V mA mA V V V V V V V mV mV mV mV mV mV V V V V V V mV mV mV mV mV mV V ms ms ms V ms kW V V V V
2003 Oct 29
4
Philips Semiconductors
Product data
One-cell Lithium-ion battery protection with over/undercharge and overcurrent protection
SA57608
TECHNICAL DISCUSSION Lithium cell safety
Lithium-ion and lithium-polymer cells have a higher energy density than that of nickel-cadmium or nickel metal hydride cells and have a much lighter weight. This makes the lithium cells attractive for use in portable products. However, lithium cells require a protection circuit within the battery pack because certain operating conditions can be hazardous to the battery or the operator, if allowed to continue. Lithium cells have a porous carbon or graphite anode where lithium ions can lodge themselves in the pores. The lithium ions are separated, which avoids the hazards of metallic lithium. If the lithium cell is allowed to become overcharged, metallic lithium plates out onto the surface of the anode and volatile gas is generated within the cell. This creates a rapid-disassembly hazard (the battery ruptures). If the cell is allowed to over-discharge (Vcell less than approximately 2.3 V), then the copper metal from the cathode goes into the electrolyte solution. This shortens the cycle life of the cell, but presents no safety hazard. If the cell experiences excessive charge or discharge currents, as happens if the wrong charger is used, or if the terminals short circuit, the internal series resistance of the cell creates heating and generates the volatile gas which could rupture the battery. The protection circuit continuously monitors the cell voltage for an overcharged condition or an overdischarged condition. It also continuously monitors the output for an overcurrent condition. If any of these conditions are encountered, the protection circuit opens a series MOSFET switch to terminate the abnormal condition. The lithium cell protection circuit is placed within the battery pack very close to the cell. Charging control versus battery protection The battery pack industry does not recommend using the pack's internal protection circuit to end the charging process. The external battery charger should have a charge termination circuit in it, such
as that provided by the SA57611. This provides two levels of overcharge protection, with the primary protection of the external charge control circuit and the backup protection from the battery pack's protection circuit. The charge termination circuit will be set to stop charging at a level around 50 mV less than the overvoltage threshold voltage of the battery pack's own protection circuit.
Lithium cell operating characteristics
The internal resistance of lithium cells is in the 100 m range, compared to the 5-20 m of the nickel-based batteries. This makes the Lithium-ion and polymer cells better for lower battery current applications (less than 1 ampere) as found in cellular and wireless telephones, palmtop and laptop computers, etc. The average operating voltage of a lithium-ion or polymer cell is 3.6 V as compared to the 1.2 V of NiCd and NiMH cells. The typical discharge curve for Lithium cell is shown in Figure 3.
OPEN-CIRCUIT CELL VOLTAGE (V)
4.0
VOV
3.0
VUV 2.0 50 NORMALIZED CELL CAPACITY (%)
100
SL01553
Figure 3. Lithium discharge curve.
2003 Oct 29
5
Philips Semiconductors
Product data
One-cell Lithium-ion battery protection with over/undercharge and overcurrent protection
SA57608
Charging Lithium cells
The lithium cells must be charged with a dedicated charging IC such as the NE57600. These dedicated charging ICs perform a current-limited, constant-voltage charge, as shown in Figure 4. The charger IC begins charging with a current that is typically the rating of the cell (1C) or the milliampere rating of the cell. As the cell approaches its full-charge voltage rating (VOV), the current entering the cell decreases, and the charger IC provides a constant voltage. When the charge current falls below a preset amount, 50 mA for example, the charge is discontinued. If charging is begun below the overdischarged voltage rating of the cell, it is important to slowly raise the cell voltage up to this overdischarged voltage level. This is done by a reconditioning charge. A small amount of current is provided to the cell (50 mA for example), and the cell voltage is allowed a period of time to rise to the overdischarged voltage. If the cell voltage recovers, then a normal charging sequence can begin. If the cell does not reach the overdischarged voltage level, then the cell is too damaged to charge and the charge is discontinued. To take advantage of the larger energy density of lithium cells it is important to allow enough time to completely charge the cell . When the charger switches from constant current to constant voltage charge (Point B, Figure 4) the cell only contains about 80 percent of its full capacity. When the cell is 100 mV less than its full rated charge voltage the capacity contained within the cell is 95 percent. Hence, allowing the cell to slowly complete its charge takes advantage of the larger capacity of the lithium cells.
SA57608 OPERATION
The SA57608 continuously monitors the terminal voltage and battery pack current of a single Li-ion battery pack. Li-ion cells must be maintained within a set of a very defined operating conditions to operate safely and with with a long life. If the cell voltage exceeds the cell's full-charge voltage, the charge current is interrupted. If the cell voltage falls below the overdischarge rating of the cell, the discharge current is interrupted. Also, whenever the discharge current exceeds the threshold voltage across the RDS(on) of the two MOSFETs, the short-circuit current is interrupted.
VCC OV DELAY CONTROL CF
VCC
OV
UV
CDLY
VREF GND CHARGER DETECTOR V- OC REF UV DELAY CONTROL VCC DF
SL01579
1.0 CHARGE CURRENT (%C)
Figure 5. SA57608 block diagram.
Overvoltage condition
0.5 CONSTANT CURRENT CONSTANT VOLTAGE
1.0 TIME (HOURS)
2.0
Vov OPEN-CIRCUIT CELL VOLTAGE (V)
When the cell's terminal voltage exceeds the value of VOV1, measured from VCC (pin 5) to GND (pin 6), the overvoltage time delay is initiated. After this time has elapsed, the gate of the charge MOSFET (CF, pin 3) is driven LOW and the charge current is interrupted. The terminal voltage of the cell may immediately fall due to the amount of the charge current times the series resistance of the Li-ion cell (Ichg x RESR). The charge MOSFET will not turn on again until the cell voltage has fallen below VOV(rel), or when a load is detected across the battery pack terminals. A load is detected when the VM pin (pin 2) is drawn 0.7 V above the cell's negative terminal (GND, pin 6). The timing capacitor CDLY (pin 4) provides a time period between the overvoltage threshold (VOV1) being exceeded and when the charge MOSFET is turned off. Its timing period is approximately:
4.0
Point B
tDLY = CDLY (VCC - 0.7 V) / 0.43 A
(Equation 1)
3.0
The variation in timing is approximately 16 percent.
1.0 TIME (HOURS)
2.0
SL01554
Figure 4. Lithium Cell charging Curves
2003 Oct 29
6
Philips Semiconductors
Product data
One-cell Lithium-ion battery protection with over/undercharge and overcurrent protection
SA57608
Undervoltage condition
When the cell voltage falls below the overdischarge threshold, (VUV1), as measured between VCC (pin 5) and GND (pin 6), the gate of the discharge MOSFET (DF, pin 1) is brought LOW (OFF) after an internal time delay. The SA57608 then assumes a sleep condition where its ICC assumes a very low state (ICC(SLP)) The gate is then brought HIGH (ON) when a charge current is detected, or when the VM pin (pin 2) is brought to 0.7 V higher than the negative terminal of the cell (GND, pin 6) or when the cell voltage is higher than the hysteresis voltage (VUV2).
If the battery pack is being charged, and the cell's voltage exceeds the overvoltage threshold, then the charge MOSFET is turned OFF (FET towards the pack's external terminal). The cell's voltage must fall lower than the overvoltage hysteresis voltage (VOV(Hyst)) before the charge MOSFET is again turned ON. If the battery pack is being discharged and the undervoltage threshold (VUV(Th)) is exceeded, then the discharge MOSFET is turned OFF. It will not run back ON until a charger is applied to the pack's external terminals and the cell's voltage rises above the undervoltage hysteresis voltage (VUV(Hyst)). When the battery pack is being discharged, the load current causes the voltage across the discharge MOSFET to increase past the overcurrent threshold voltage (VOC(TH)), then the discharge MOSFET is turned OFF after a fixed 7-18 ms delay. If short-circuit is placed across the pack's terminals, then the discharge MOSFET is turned OFF after a 100-300 s time delay to avoid damaging the MOSFETs.
Discharge overcurrent condition
If a discharge overcurrent condition is experienced as seen when a short-circuit is experienced across the battery terminals, the SA57608 views a high voltage across the MOSFET's RDS(on). If this voltage exceeds the threshold voltage (VSC), the discharge gate is brought to a LOW condition (OFF) after an internally set of time delays are exceeded. If the overcurrent is LOW, then the tSC1 is enacted. If the the overcurrent is higher, as experienced in a hard short-circuit, the time delay is less than 400 ns. This prevents the MOSFETs from failing from an FBSOA failure. The gate of the discharge MOSFET is turned on again only when the voltage of the VM pin is allowed to fall within the 0.7 volts of the negative terminal of the cell (GND, Pin 6). If the short-circuit persists, the gate of the discharge MOSFET is immediately brought LOW (OFF) again until the short-circuit condition is again removed.
The R-C filter on the VCC pin
One needs to place an R-C filters on the VCC pin. It is to primarily shield the IC from electrostatic occurrences and spikes on the terminals of the battery pack. A secondary need is during the occurrence of a short-circuit across the battery pack terminals. Here, the Li-ion cell voltage could collapse and cause the IC to enter an unpowered state. The R-Cs then provide power during the first instant of the short circuit and allow the IC to turn OFF the discharge MOSFET. The IC can then enter an unpowered state. Lastly, the R-C filter filters any noise voltage caused by noisy load current. The values shown in Figure 6 are good for these purposes.
APPLICATION INFORMATION
The typical single-cell lithium-ion or polymer protection circuit based upon the SA57608 is seen in Figure 6.
Selecting the Optimum MOSFETs:
For a single-cell battery pack, a logic-level MOSFET should be used. These MOSFETs have turn-on thresholds of 0.9 V and are considered full-ON at 4.5 V VGS. Some problem may be encountered in not having enough gate voltage to fully turn-ON the series MOSFETs over the battery pack's entire operating voltage. If one deliberately selects an N-Channel MOSFET with a much greater current rating, a lower RDS(on) over the entire range can be attained. The MOSFETs should have a voltage rating greater than 20 V and should have a high avalanche rating to survive any spikes generated across the battery pack terminals. The current rating of the MOSFETs should be greater than four times the maximum "C-rating" of the cells. The current rating, though, is more defined by the total series resistance of the battery pack. The total resistance of the battery pack is given by Equation 2. Rbat(tot) = RDS(on) + Rcell (Equation 2)
V+ 100 0.01 F 0.1 F 4 Li-ION CELL 6 GND CDLY 5 VCC
SA57608
2 VM
DF 1
CF 3
0.1 F
1 k V-
DISCHARGE FET
CHARGE FET
SL01570
The total pack resistance is typically determined by the system requirements. The total pack resistance directly determines how much voltage droop will occur during pulses in load current. Another consideration is the forward-biased safe operating area of the MOSFET. During a short-circuit, the discharge current can easily reach 10-15 times the "C-rating" of the cells. The MOSFET must survive this current prior to the discharge MOSFET can be turned OFF. So having an FBSOA envelope that exceeds 20 amperes for 5 ms would be safe.
Figure 6. Typical protection circuit The SA57608 drives the series N-Channel MOSFETs to states determined by the cell's voltage and the battery pack load current. During normal periods of operation, both the discharge and charge MOSFETs are in the ON state, thus allowing bidirectional current flow.
2003 Oct 29
7
Philips Semiconductors
Product data
One-cell Lithium-ion battery protection with over/undercharge and overcurrent protection
SA57608
PACKING METHOD
GUARD BAND TAPE REEL ASSEMBLY
TAPE DETAIL
COVER TAPE
CARRIER TAPE
BARCODE LABEL
BOX
SL01305
2003 Oct 29
8
Philips Semiconductors
Product data
One-cell Lithium-ion battery protection with over/undercharge and overcurrent protection
SA57608
Plastic small outline package; 6 leads; body width 1.8 mm
SOP004
2003 Oct 29
9
Philips Semiconductors
Product data
One-cell Lithium-ion battery protection with over/undercharge and overcurrent protection
SA57608
REVISION HISTORY
Rev _1 Date yyyymmdd Description Product data (9397 750 12192). ECN 853-2298 30337 of 09 September 2003. Supersedes data of 2001 Oct 03 (9397 750 08994).
* Change package outline version to SOP004 in Ordering information table and Package outline sections.
_1 20011003 Product data (9397 750 08994). ECN 853-2298 27198 of 03 October 2001.
Modifications:
Data sheet status
Level
I
Data sheet status [1]
Objective data
Product status [2] [3]
Development
Definitions
This data sheet contains data from the objective specification for product development. Philips Semiconductors reserves the right to change the specification in any manner without notice. This data sheet contains data from the preliminary specification. Supplementary data will be published at a later date. Philips Semiconductors reserves the right to change the specification without notice, in order to improve the design and supply the best possible product. This data sheet contains data from the product specification. Philips Semiconductors reserves the right to make changes at any time in order to improve the design, manufacturing and supply. Relevant changes will be communicated via a Customer Product/Process Change Notification (CPCN).
II
Preliminary data
Qualification
III
Product data
Production
[1] Please consult the most recently issued data sheet before initiating or completing a design. [2] The product status of the device(s) described in this data sheet may have changed since this data sheet was published. The latest information is available on the Internet at URL http://www.semiconductors.philips.com. [3] For data sheets describing multiple type numbers, the highest-level product status determines the data sheet status.
Definitions
Short-form specification -- The data in a short-form specification is extracted from a full data sheet with the same type number and title. For detailed information see the relevant data sheet or data handbook. Limiting values definition -- Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 60134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information -- Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or modification.
Disclaimers
Life support -- These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application. Right to make changes -- Philips Semiconductors reserves the right to make changes in the products--including circuits, standard cells, and/or software--described or contained herein in order to improve design and/or performance. When the product is in full production (status `Production'), relevant changes will be communicated via a Customer Product/Process Change Notification (CPCN). Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified.
Contact information
For additional information please visit http://www.semiconductors.philips.com. Fax: +31 40 27 24825
(c) Koninklijke Philips Electronics N.V. 2003 All rights reserved. Printed in U.S.A. Date of release: 10-03
For sales offices addresses send e-mail to: sales.addresses@www.semiconductors.philips.com.
Document order number:
9397 750 12192
Philips Semiconductors
2003 Oct 29 10

▲Up To Search▲

Price & Availability of SA57608

	To Download SA57608 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .